The commonly used milk tea equipment is also one of the necessary milk tea shop equipment. The sealing machine is divided into three types: automatic, semi-automatic, and hand-supported sealing machine. Because the sealing machine is the most commonly used milk tea shop equipment, improper operation or mistakes will occur. The operation is a lot of trouble, which has a great impact on the operation of milk tea. The following is the correct operation method of the sealing machine, as well as troubleshooting, equipment maintenance and other methods for your reference and learning.

1. Wear film:

  1. Turn off the power first when using the film, then confirm the winding direction of the film, find the counterclockwise direction, and place it on the front film rod to fix it;

  2. Pay attention to whether the front and rear fixed splints of the film are tightly combined with the film. If they cannot be tightly combined, use a utility knife to cut the inside of the film paper tube obliquely and then put it in;

  3. After putting on the film, stick the film firmly on the take-up reel of the rear film rod with tape.

  

    2. Operation steps of pearl milk tea equipment sealing machine:

  1. Turn on the power, turn on the power switch on the panel, the indicator light is on, set the thermostat to the predetermined temperature, and the green heating indicator light is on. When the upper hot plate reaches the predetermined temperature, the red constant temperature indicator light is on. After the sealing machine is working, the electric heating device is constantly alternating between heating and heat preservation, that is, the green and red indicator lights will be displayed alternately;

  2. Put the plastic cup into the lower die slide, push the lower die slide to a certain position by hand, press down the handle of the sealing machine to the maximum stroke, and keep the pressure for 1-2 seconds. Then slowly raise the handle and push it to the original position;

  3. Take out the lower mold slide, take out the plastic cup, put in the unsealed plastic cup, and proceed to the next cycle.

3, milk tea shop equipment sealing machine precautions:

  1. Connect the ground wire to ensure the safety of electricity;

  2. When the machine fails, the power supply should be turned off first, and the fault should be removed after returning to normal temperature;

  3. The working voltage should be kept at 220V±5;

  4. The upper and lower molds must be aligned before the handle can be completely pressed;

  5. After the handle is pressed down, do not use too much force;

  6. Do not put your hand between the upper and lower molds during use to avoid being crushed and scalded.

  

    Fourth, the fault and solution of the equipment sealing machine in the milk tea shop:

1. The cup mouth is not tightly sealed and leaks: a. Turn off the power supply, and wipe clean after the pressure plate in the upper mold returns to normal temperature. B. Adjust the film to make it flat and stretch. C. Wipe the cup mouth clean and then seal.d , adjust the temperature;

  2. The incision of the plastic film at the mouth of the cup is not smooth or cuts continuously: a. Clean the toothed knife. b. Repair or replace the toothed knife;

  3. There is obvious noise in the movement of the machine: a. Remove the upper cover and find out the source of the noise. b. Add butter to the part where the noise is emitted.

  

5. Cleaning and maintenance of milk tea equipment sealing machine:

  1. Regularly clean the surface of the machine, the bottom plate and the groove of the lower slide plate, and the positioning rod of the upper mold inner pressure plate under the power off and normal temperature;

  2. The lower die slide plate, the pressure rod bearing, the eccentric wheel and the guide column, the guide rail and other transmission parts are regularly greased. To ensure the performance of the machine;

3. Method of cleaning the tooth knife: first plug the two drain holes of the lower film with cotton balls, pour boiling water into the groove of the lower mold until it is full, then push the lower mold slide into place, and press the upper mold down , press to the lowest point, let the tooth knife soak for several minutes, repeat several times until it is clean.



In order to express its concern for all kinds of milk tea shops, Jiangxi Boguang Intelligent Equipment Co., Ltd. hereby writes the correct use method of the pearl milk tea sealing machine. If you have any other questions, you can contact our customer service, they will professionally answer all kinds of milk tea shop questions for you.